200 Series Low Pressure Diaphragm Dry Pressure Gauges
*PRODUCT IMAGE IS REPRESENTATIVE PROVIDED BY THE MANUFACTURER. DO NOT MAKE BUYING DECISIONS SOLEY BASED ON THE IMAGE. PLEASE VERIFY SPECIFICATIONS MEET YOUR REQUIREMENTS.
Sensitive capsule-type non-fillable dry gauge
Black painted Steel, Stainless Steel and impact-resistant ABS case
WARNING: This product can expose you to chemicals including Lead and Nickel, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Bourdon tube pressure gauges must be used within their calibrated maximum range to prevent damage
The pressure gauges must be operated within the following working pressure limits:
Dynamic Pressure application, 60% of the dial range
Static Pressure applications, where no sharp fluctuations occur, 90% of the dial range
The gauges must be operated within specified ambient temperature ranges
Determination of gauge failures will be made by NOSHOK, Inc., which will use its equipment and personnel or a certified test facility specializing in this type of evaluation and determination. Gauge failures determined to be caused by over-range, incompatibility with environment or product media and abuse will not be considered under this warranty. NOSHOK, Inc. will, at its discretion, repair or replace the working parts of the damaged gauge without cost to the customer. This written warranty applies only to the NOSHOK gauges referenced in the first paragraph of this warranty, sold by NOSHOK, Inc. and its authorized distributors.
1
NOSHOK's Distribution Manifolds connect multiple instruments to one diaphragm seal, eliminating multiple connections that lead to possible leak paths.
Operating conditions including, but not limited to, system pressure, media compatibility and ambient conditions must be considered when selecting gauges and accessories. Improper selections and use of gauges could possibly cause gauge failure and lead to possible property damage or personal injury. Refer to the American National Standard ANSI B40.1 for the correct selection and use of gauges. A copy of this standard may be obtained from the American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, NY 10017.
In keeping with and for purposes of product and/or manufacturing process improvements, NOSHOK, Inc. reserves the right to make design changes without prior notice.
102-MFB, 1/4" National Pipe Thread (NPT), Male x Female, Brass, 0.172" Orifice Hard Seat Mini Valve 102-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, 0.172" Orifice Hard Seat Mini Valve 102-MFS, 1/4" National Pipe Thread (NPT), Male x Female, 316 Stainless Steel, 0.172" Orifice Hard Seat Mini Valve 602-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, Hard Seat, 0.187" Orifice Block and Bleed Valve
Protect the instrument from the damaging effects of high temperature steam
Recommended for use in all steam applications
Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3800 psi at 850 ºF
0 to 10 psi
NOSHOK offers a wide variety of standard & elevated pressure, and reduced pressure replaceable and non-replaceable diaphragm seals, designed to isolate and/or protect the pressure measuring instrument from corrosive, viscous, contaminated or very high temperature process media.
Temperature ratings: 15,000 psi at 200 ºF and 3,000 psi at 1,000 ºF
Used with gauges and gauge valves to adjust the line of sight
Rotates 360º to allow the connected instrument to be positioned in the desired direction
The pressure connection is achieved with a tapered cone style compression fitting simply by tightening the swivel hex nut
All 316 Stainless Steel construction
Standard with 1/2" NPT male process - 1/2" NPT female instrument connections
Also available with 1/4" NPT connections, same specifications apply
Weight approximately 0.8 lb.
1/4 in
-20 to 80
-4 to 176
0 to 10 psi
Protect the instrument from the damaging effects of high temperature steam
Recommended for use in all steam applications
Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3800 psi at 850 ºF
Temperature ratings: 15,000 psi at 200 ºF and 3,000 psi at 1,000 ºF
Used with gauges and gauge valves to adjust the line of sight
Rotates 360º to allow the connected instrument to be positioned in the desired direction
The pressure connection is achieved with a tapered cone style compression fitting simply by tightening the swivel hex nut
All 316 Stainless Steel construction
Standard with 1/2" NPT male process - 1/2" NPT female instrument connections
Also available with 1/4" NPT connections, same specifications apply
Weight approximately 0.8 lb.
Available
Stainless Steel Case (SSC)
Glass Lens (GL) (A steel or stainless cover ring must be additionally ordered when lenses other than plexiglass are utilized on all 200 Series models)
Safety Glass Lens (SG) (A steel or stainless cover ring must be additionally ordered when lenses other than plexiglass are utilized on all 200 Series models)
Plexiglass Lens (PL)
Recalibrator Lens (RL)
Red Set Pointer (SP)
Maximum Indicating Pointer (MIP)
Black Rear Flange (BLRF)
Black Cover Ring (BCR)
Stainless Steel Cover Ring (SSCR)
Rubber Case Protectors (RCP)
10-32-UNF-2B (10-32)
Orifice - Brass Threaded 0.3mm (BT3) - Standard
Laser Marking (LM)
Stainless Steel Tagging (ST)
Certificates
Certified Calibration (CC)
±1.6% Full Scale
NOSHOK offers multiple assembly options to meet your specific system requirements. Consult factory to discuss your customized solution.
Copper Alloy Diaphragm Capsule
<ul><li>Certificate of Cleaning (COCL)</li><li>Certificate of Conformance (COC)</li></ul>
Dynamic Pressure The working pressure should be limited to 60% of the dial range
Static Pressure The working pressure, where no sharp fluctuations occur, should be limited to 90% of the dial range
Dual scale metric dials in psi/bar, psi/kPa and psi/kg/cm2
Other scales are available for specific sizes and ranges, such as single scale bar and kPa, refrigerant scales and altitude scales
Customized special dials such as non-standard metric scale, tons of ram, lbs. of force, etc. are available in small quantities (as few as one piece) on some NOSHOK gauges
Please consult the factory for availability.
Inch
2-1/2
Acrylic
National Pipe Thread (NPT)
1/4" NPT
Bottom
Brass
Black Finished Aluminum
-20 to 60
-4 to 140
1/4 in National Pipe Thread (NPT)
200
Aluminum, white background with black scale. UV resistant.
Low Pressure Gauge
Black Painted Steel
Brass and Nickel-Silver with Highly Polished Bearing Surfaces
Steel, Bottom Connection
Black Painted Steel
Aluminum, white background with black scale. UV resistant.
WARNING: This product can expose you to chemicals including Lead and Nickel, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Bourdon tube pressure gauges must be used within their calibrated maximum range to prevent damage
The pressure gauges must be operated within the following working pressure limits:
Dynamic Pressure application, 60% of the dial range
Static Pressure applications, where no sharp fluctuations occur, 90% of the dial range
The gauges must be operated within specified ambient temperature ranges
Determination of gauge failures will be made by NOSHOK, Inc., which will use its equipment and personnel or a certified test facility specializing in this type of evaluation and determination. Gauge failures determined to be caused by over-range, incompatibility with environment or product media and abuse will not be considered under this warranty. NOSHOK, Inc. will, at its discretion, repair or replace the working parts of the damaged gauge without cost to the customer. This written warranty applies only to the NOSHOK gauges referenced in the first paragraph of this warranty, sold by NOSHOK, Inc. and its authorized distributors.
1
NOSHOK's Distribution Manifolds connect multiple instruments to one diaphragm seal, eliminating multiple connections that lead to possible leak paths.
Operating conditions including, but not limited to, system pressure, media compatibility and ambient conditions must be considered when selecting gauges and accessories. Improper selections and use of gauges could possibly cause gauge failure and lead to possible property damage or personal injury. Refer to the American National Standard ANSI B40.1 for the correct selection and use of gauges. A copy of this standard may be obtained from the American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, NY 10017.
In keeping with and for purposes of product and/or manufacturing process improvements, NOSHOK, Inc. reserves the right to make design changes without prior notice.
102-MFB, 1/4" National Pipe Thread (NPT), Male x Female, Brass, 0.172" Orifice Hard Seat Mini Valve 102-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, 0.172" Orifice Hard Seat Mini Valve 102-MFS, 1/4" National Pipe Thread (NPT), Male x Female, 316 Stainless Steel, 0.172" Orifice Hard Seat Mini Valve 602-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, Hard Seat, 0.187" Orifice Block and Bleed Valve
Protect the instrument from the damaging effects of high temperature steam
Recommended for use in all steam applications
Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3800 psi at 850 ºF
0 to 15 oz/in²
NOSHOK offers a wide variety of standard & elevated pressure, and reduced pressure replaceable and non-replaceable diaphragm seals, designed to isolate and/or protect the pressure measuring instrument from corrosive, viscous, contaminated or very high temperature process media.
Temperature ratings: 15,000 psi at 200 ºF and 3,000 psi at 1,000 ºF
Used with gauges and gauge valves to adjust the line of sight
Rotates 360º to allow the connected instrument to be positioned in the desired direction
The pressure connection is achieved with a tapered cone style compression fitting simply by tightening the swivel hex nut
All 316 Stainless Steel construction
Standard with 1/2" NPT male process - 1/2" NPT female instrument connections
Also available with 1/4" NPT connections, same specifications apply
Weight approximately 0.8 lb.
1/4 in
-20 to 80
-4 to 176
0 to 15 oz/in²
Protect the instrument from the damaging effects of high temperature steam
Recommended for use in all steam applications
Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3800 psi at 850 ºF
Temperature ratings: 15,000 psi at 200 ºF and 3,000 psi at 1,000 ºF
Used with gauges and gauge valves to adjust the line of sight
Rotates 360º to allow the connected instrument to be positioned in the desired direction
The pressure connection is achieved with a tapered cone style compression fitting simply by tightening the swivel hex nut
All 316 Stainless Steel construction
Standard with 1/2" NPT male process - 1/2" NPT female instrument connections
Also available with 1/4" NPT connections, same specifications apply
Weight approximately 0.8 lb.
Available
Stainless Steel Case (SSC)
Glass Lens (GL) (A steel or stainless cover ring must be additionally ordered when lenses other than plexiglass are utilized on all 200 Series models)
Safety Glass Lens (SG) (A steel or stainless cover ring must be additionally ordered when lenses other than plexiglass are utilized on all 200 Series models)
Plexiglass Lens (PL)
Recalibrator Lens (RL)
Red Set Pointer (SP)
Maximum Indicating Pointer (MIP)
Black Rear Flange (BLRF)
Black Cover Ring (BCR)
Stainless Steel Cover Ring (SSCR)
Rubber Case Protectors (RCP)
10-32-UNF-2B (10-32)
Orifice - Brass Threaded 0.3mm (BT3) - Standard
Laser Marking (LM)
Stainless Steel Tagging (ST)
Certificates
Certified Calibration (CC)
±1.6% Full Scale
NOSHOK offers multiple assembly options to meet your specific system requirements. Consult factory to discuss your customized solution.
Copper Alloy Diaphragm Capsule
<ul><li>Certificate of Cleaning (COCL)</li><li>Certificate of Conformance (COC)</li></ul>
Dynamic Pressure The working pressure should be limited to 60% of the dial range
Static Pressure The working pressure, where no sharp fluctuations occur, should be limited to 90% of the dial range
Dual scale metric dials in psi/bar, psi/kPa and psi/kg/cm2
Other scales are available for specific sizes and ranges, such as single scale bar and kPa, refrigerant scales and altitude scales
Customized special dials such as non-standard metric scale, tons of ram, lbs. of force, etc. are available in small quantities (as few as one piece) on some NOSHOK gauges
Please consult the factory for availability.
Inch
2-1/2
Acrylic
National Pipe Thread (NPT)
1/4" NPT
Bottom
Brass
Black Finished Aluminum
-20 to 60
-4 to 140
1/4 in National Pipe Thread (NPT)
200
Aluminum, white background with black scale. UV resistant.
Low Pressure Gauge
Black Painted Steel
Brass and Nickel-Silver with Highly Polished Bearing Surfaces
Steel, Bottom Connection
Black Painted Steel
Aluminum, white background with black scale. UV resistant.
WARNING: This product can expose you to chemicals including Lead and Nickel, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Bourdon tube pressure gauges must be used within their calibrated maximum range to prevent damage
The pressure gauges must be operated within the following working pressure limits:
Dynamic Pressure application, 60% of the dial range
Static Pressure applications, where no sharp fluctuations occur, 90% of the dial range
The gauges must be operated within specified ambient temperature ranges
Determination of gauge failures will be made by NOSHOK, Inc., which will use its equipment and personnel or a certified test facility specializing in this type of evaluation and determination. Gauge failures determined to be caused by over-range, incompatibility with environment or product media and abuse will not be considered under this warranty. NOSHOK, Inc. will, at its discretion, repair or replace the working parts of the damaged gauge without cost to the customer. This written warranty applies only to the NOSHOK gauges referenced in the first paragraph of this warranty, sold by NOSHOK, Inc. and its authorized distributors.
1
NOSHOK's Distribution Manifolds connect multiple instruments to one diaphragm seal, eliminating multiple connections that lead to possible leak paths.
Operating conditions including, but not limited to, system pressure, media compatibility and ambient conditions must be considered when selecting gauges and accessories. Improper selections and use of gauges could possibly cause gauge failure and lead to possible property damage or personal injury. Refer to the American National Standard ANSI B40.1 for the correct selection and use of gauges. A copy of this standard may be obtained from the American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, NY 10017.
In keeping with and for purposes of product and/or manufacturing process improvements, NOSHOK, Inc. reserves the right to make design changes without prior notice.
402-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, Hard Seat, 0.187" Orifice Needle Valve 602-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, Hard Seat, 0.187" Orifice Block and Bleed Valve 602-MFS, 1/4" National Pipe Thread (NPT), Male x Female, 316 Stainless Steel, Hard Seat, 0.187" Orifice Block and Bleed Valve 702-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, Soft Seat, 0.187" Orifice Block and Bleed Valve
Protect the instrument from the damaging effects of high temperature steam
Recommended for use in all steam applications
Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3800 psi at 850 ºF
0 to 60 inH2O
NOSHOK offers a wide variety of standard & elevated pressure, and reduced pressure replaceable and non-replaceable diaphragm seals, designed to isolate and/or protect the pressure measuring instrument from corrosive, viscous, contaminated or very high temperature process media.
Temperature ratings: 15,000 psi at 200 ºF and 3,000 psi at 1,000 ºF
Used with gauges and gauge valves to adjust the line of sight
Rotates 360º to allow the connected instrument to be positioned in the desired direction
The pressure connection is achieved with a tapered cone style compression fitting simply by tightening the swivel hex nut
All 316 Stainless Steel construction
Standard with 1/2" NPT male process - 1/2" NPT female instrument connections
Also available with 1/4" NPT connections, same specifications apply
Weight approximately 0.8 lb.
1/4 in
-20 to 80
-4 to 176
0 to 60 inH2O
Protect the instrument from the damaging effects of high temperature steam
Recommended for use in all steam applications
Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3800 psi at 850 ºF
Temperature ratings: 15,000 psi at 200 ºF and 3,000 psi at 1,000 ºF
Used with gauges and gauge valves to adjust the line of sight
Rotates 360º to allow the connected instrument to be positioned in the desired direction
The pressure connection is achieved with a tapered cone style compression fitting simply by tightening the swivel hex nut
All 316 Stainless Steel construction
Standard with 1/2" NPT male process - 1/2" NPT female instrument connections
Also available with 1/4" NPT connections, same specifications apply
Weight approximately 0.8 lb.
Available
Stainless Steel Case (SSC)
Glass Lens (GL) (A steel or stainless cover ring must be additionally ordered when lenses other than plexiglass are utilized on all 200 Series models)
Safety Glass Lens (SG) (A steel or stainless cover ring must be additionally ordered when lenses other than plexiglass are utilized on all 200 Series models)
Plexiglass Lens (PL)
Recalibrator Lens (RL)
Red Set Pointer (SP)
Maximum Indicating Pointer (MIP)
Black Rear Flange (BLRF)
Black Cover Ring (BCR)
Stainless Steel Cover Ring (SSCR)
Rubber Case Protectors (RCP)
10-32-UNF-2B (10-32)
Orifice - Brass Threaded 0.3mm (BT3) - Standard
Laser Marking (LM)
Stainless Steel Tagging (ST)
Certificates
Certified Calibration (CC)
±1.6% Full Scale
NOSHOK offers multiple assembly options to meet your specific system requirements. Consult factory to discuss your customized solution.
Copper Alloy Diaphragm Capsule
<ul><li>Certificate of Cleaning (COCL)</li><li>Certificate of Conformance (COC)</li></ul>
Dynamic Pressure The working pressure should be limited to 60% of the dial range
Static Pressure The working pressure, where no sharp fluctuations occur, should be limited to 90% of the dial range
Dual scale metric dials in psi/bar, psi/kPa and psi/kg/cm2
Other scales are available for specific sizes and ranges, such as single scale bar and kPa, refrigerant scales and altitude scales
Customized special dials such as non-standard metric scale, tons of ram, lbs. of force, etc. are available in small quantities (as few as one piece) on some NOSHOK gauges
Please consult the factory for availability.
Inch
4
Instrument glass
National Pipe Thread (NPT)
1/4" NPT
Bottom
Brass
Black Finished Aluminum
-20 to 60
-4 to 140
1/4 in National Pipe Thread (NPT)
200
Aluminum, white background with black scale. UV resistant.
Low Pressure Gauge
304 Stainless Steel
Brass and Nickel-silver with highly polished bearing surfaces
304 Stainless Steel, Bottom Connection
304 Stainless Steel
Aluminum, white background with black scale. UV resistant.
WARNING: This product can expose you to chemicals including Lead and Nickel, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
