| UOM | EA | Note | Please consult your local NOSHOK Distributor or NOSHOK, Inc. for availability and delivery information. |
| Application | - Automotive
- Construction
- Hydraulics & pneumatics
- Power generation
- Transportation
- Water management
| Prop 65 Warnings |  WARNING: This product can expose you to chemicals including Lead and Nickel, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov |
| Limitations Which Apply Are | - Bourdon tube pressure gauges must be used within their calibrated maximum range to prevent damage
- The pressure gauges must be operated within the following working pressure limits:
- Dynamic Pressure application, 60% of the dial range
- Static Pressure applications, where no sharp fluctuations occur, 90% of the dial range
- The gauges must be operated within specified ambient temperature ranges
- Determination of gauge failures will be made by NOSHOK, Inc., which will use its equipment and personnel or a certified test facility specializing in this type of evaluation and determination. Gauge failures determined to be caused by over-range, incompatibility with environment or product media and abuse will not be considered under this warranty. NOSHOK, Inc. will, at its discretion, repair or replace the working parts of the damaged gauge without cost to the customer. This written warranty applies only to the NOSHOK gauges referenced in the first paragraph of this warranty, sold by NOSHOK, Inc. and its authorized distributors.
| Warranty_yr | 3 |
| Distribution Manifolds | NOSHOK's Distribution Manifolds connect multiple instruments to one diaphragm seal, eliminating multiple connections that lead to possible leak paths. | Caution | Operating conditions including, but not limited to, system pressure, media compatibility and ambient conditions must be considered when selecting gauges and accessories. Improper selections and use of gauges could possibly cause gauge failure and lead to possible property damage or personal injury. Refer to the American National Standard ANSI B40.1 for the correct selection and use of gauges. A copy of this standard may be obtained from the American Society of Mechanical Engineers, United Engineering Center, 345 East 47th Street, New York, NY 10017.
In keeping with and for purposes of product and/or manufacturing process improvements, NOSHOK, Inc. reserves the right to make design changes without prior notice. |
| Related Items | 102-MFB, 1/4" National Pipe Thread (NPT), Male x Female, Brass, 0.172" Orifice Hard Seat Mini Valve 102-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, 0.172" Orifice Hard Seat Mini Valve 102-MFS, 1/4" National Pipe Thread (NPT), Male x Female, 316 Stainless Steel, 0.172" Orifice Hard Seat Mini Valve 602-MFC, 1/4" National Pipe Thread (NPT), Male x Female, Steel, Hard Seat, 0.187" Orifice Block and Bleed Valve | Steam Syphons | - Protect the instrument from the damaging effects of high temperature steam
- Recommended for use in all steam applications
- Available in 1/4" and 1/2" NPT sizes in welded steel, welded 316 Stainless Steel or seamless 316 Stainless Steel with ratings to 3800 psi at 850 ºF
|
| Pressure Range | 0 to 1,000 psi | Diaphragm Seals | NOSHOK offers a wide variety of standard & elevated pressure, and reduced pressure replaceable and non-replaceable diaphragm seals, designed to isolate and/or protect the pressure measuring instrument from corrosive, viscous, contaminated or very high temperature process media. |
| Process Connection Size | 1/4 in. National Pipe Thread (NPT) or 7/16 in.-20 Adjustable, Brass | Media Temperature Range_ºC | -20 to 60 |
| Media Temperature Range_ºF | -4 to 140 | Pressure Range (Search only) | 0 to 1,000 psi |
| Pressure Snubbers - Piston Type | - Resist clogging and are self-cleaning
- Five different sized pistons included with each snubber to ensure the correct amount of snubbing for virtually every application
- Available in Brass and 316 Stainless Steel in 1/4" NPT, 1/2" NPT or SAE J1926-3: 7/16-20
- Weight approximately 0.2 lb. for 1/4" & 7/16", and approximately 0.4 lb. for 1/2"
| Pressure Snubbers - Sintered Type | - Cost effective solution to protect expensive instrumentation
- Increases gauge readability by smoothing out pressure surges, pulsations and spikes
- 5 basic elements available for each snubber to accommodate specific application needs
- Snubbing action achieved by utilizing a corrosion resistant 316 Stainless Steel sintered porous element
- Exotic materials or intermediate disc grades available
- Provides long service life with no moving parts to wear out
- Weight approximately 0.2 lb. for 1/4" & 7/16", and approximately 0.4 lb. for 1/2
|
| Installed Options and Accessories | Available- 1/4" NPT x G1/4 Adaptor (1/4-NPTFXG1/4M-BRASS-ADAPTER)
- G1/4 Sealing Washer (G1/4-SEALING-WASHER)
- 10-32-UNF-2B (10-32)
- Orifice - Brass Press Fit 0.3mm (BP3) - Standard
- Orifice - Brass Threaded 0.5mm (BT5)
- Laser Marking (LM)
- Stainless Steel Tagging (ST)
- -40 Degree Service (GY40) - Standard
Consult Factory- Silicone Fill (SL)
- Halocarbon Fill (HL)
- Mineral Oil Fill (MO)
- Cleaning for Oxygen Service (O2) Up to 1,000 psi
- Cleaning for Oxygen Service (O2) 1,500 psi & up
Gauge Fill Options- -40 Degree Service (GY40) - Standard
Certificates- Certified Calibration (CC)
| Accuracy | ±1.6% Full Scale |
| Measuring Element | Coiled Safety Tube | Uninstalled Options and Accessories | <ul><li>Certificate of Cleaning (COCL)</li><li>Certificate of Conformance (COC)</li></ul> |
| Working Pressure Limitations | Dynamic Pressure
The working pressure should be limited to 60% of the dial range
Static Pressure
The working pressure, where no sharp fluctuations occur, should be limited to 90% of the dial range | Warnings | Glycerin or silicone could result in a spontaneous chemical reaction or explosion when combined with strong oxidizing agents including, but not limited to, chlorine, oxygen, hydrochloric or nitric acid, and hydrogen peroxide. Do not use glycerin or silicone filled gauges or accessories in these types of service. Consult factory for application assistance.
This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. |
| Type | Pressure Gauge | Pointer | Molded Plastic |
| Material | 304 Stainless Steel | Inch/Metric | Inch |
| Gauge Size_in | 2-1/2 | Process Connection | 1/4" NPT |
| Pressure Range_psi | 0 to 1,000 | Scale Option | psi/bar Dual Scale |
| Connection Location | Bottom | Series | 900 |
| Movement | Brass and Nylon with Highly Polished Bearing Surfaces | Case Type | Stainless Steel (SS) Case, Liquid Filled, Bottom Connection |
| Bezel Material | 304 Stainless Steel | Dial/Display Size | Molded Plastic, White Background with Black Primary Scale & Red Secondary Scale. Ultraviolet (UV) Resistant. |
| Lens/Display Material | Polycarbonate | Ambient Temperature Range_ºC | -20 to 60 |
| Ambient Temperature Range_ºF | -4 to 140 | Fill Liquid | Glycerin |
| Media Temperature Range (Special Fill)_ºC | -40 to 60 | Media Temperature Range (Special Fill)_ºF | -40 to 140 |
| Media Temperature Range (Glycerin Fill)_ºC | -20 to 60 | Media Temperature Range (Glycerin Fill)_ºF | -4 to 140 |
| Ambient Temperature Range (Glycerin Fill)_ºC | -20 to 60 | Ambient Temperature Range (Glycerin Fill)_ºF | -4 to 140 |
| Joint Connection | 1/4 in. National Pipe Thread (NPT) or 7/16 in.-20 Adjustable, Brass | | |
30-300-025-0/250-F/C - 300 Series Industrial Type Bimetal Thermometers with External Reset, Sanitary Tri-Clamp® Options
40-500-10000-psi/bar - 400/500 Series All Stainless Steel Dry and Liquid Filled Pressure Gauges
25-120-160-psi/kPa - 100 Series Acrylonitrile Butadiene Styrene (ABS) and Steel Case Dry Pressure Gauges
